Alpha 1000 Uživatelská příručka Strana 58
- Strana / 200
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
3.3.1 test
The
test
command runs firmware diagnostics for the entire core system. The
tests are run concurrently in the background. Fatal errors are reported to the
console terminal.
The
cat el
command should be used in conjunction with the
test
command to
examine test/error information reported to the console event log.
Because the tests are run concurrently and indefinitely (until you stop them with
the
kill_diags
command), they are useful in flushing out intermittent hardware
problems.
Note
By default, no write tests are performed on disk and tape drives. Media
must be installed to test the floppy drive and tape drives. A loopback
connector is required for the COM2 (9-pin loopback connector, 12-27351-
01) port.
The test command does not test the DNSES, TGA card, reflective memory
option, nor third party options.
When using the
test
command after shutting down an operating system,
you must initialize the system to a quiescent state. Enter the following
commands at the SRM console:
P00>>> set auto_action halt
P00>>> init
...
P00>>> test
After testing is completed, set the auto_action environment variable to
its previous value (usually, boot) and use the Reset button to reset the
system.
To terminate the tests, use the
kill
command to terminate an individual
diagnostic or the
kill_diags
command to terminate all diagnostics. Use the
show_status
display to determine the process ID when terminating an individual
diagnostic test.
Note
A serial loopback connector (12-27351-01) must be installed on the COM2
serial port for the
kill_diags
command to successfully terminate system
tests.
3–4 Running System Diagnostics
- AlphaServer 1000A 1
- Service Guide 1
- Contents 3
- 3 Running System Diagnostics 4
- 4 Error Log Analysis 4
- A Default Jumper Settings 6
- Examples 6
- Intended Audience 11
- Conventions 12
- Related Documentation 12
- Troubleshooting Strategy 15
- 1.1.1 Problem Categories 16
- 1–8 Troubleshooting Strategy 22
- 1.3 Information Services 23
- 1–10 Troubleshooting Strategy 24
- Troubleshooting Strategy 1–11 25
- ....done 31
- 12345.done 31
- FAIL B:0 S:2 31
- 2.3 Power-Up Screen 35
- 2.3.1 Console Event Log 37
- 2.5 Storage Device LEDs 41
- Activity LED 42
- 2.8 Fail-Safe Loader 47
- 2.9 Power-Up Sequence 50
- 2.9.2 DC Power-Up Sequence 51
- 2.10.1 Serial ROM Diagnostics 51
- Running System Diagnostics 55
- 3.2 Command Summary 56
- 3.3 Command Reference 57
- 3.3.1 test 58
- 3.3.2 cat el and more el 61
- 3.3.3 memory 62
- 3.3.4 netew 64
- Testing an Ethernet Port: 65
- 3.3.5 network 66
- 3.3.6 net -s 68
- 3.3.7 net -ic 69
- 3.3.8 kill and kill_diags 70
- 3.3.9 show_status 71
- 3.5 DEC VET 72
- Error Log Analysis 73
- Error Log Analysis 4–3 75
- 4–4 Error Log Analysis 76
- 4.3 Event Record Translation 77
- 4–6 Error Log Analysis 78
- System Configuration and Setup 79
- 5.1.1 System Firmware 80
- >>> 81
- >>> set os_type NT 82
- >>> init 82
- Digital UNIX and OpenVMS 87
- Synopsis: 89
- Example: 89
- Key to variable attributes: 94
- Whenever you use the 100
- 5.2 System Bus Options 101
- 5.2.1 CPU Daughter Board 102
- 5.2.2 Memory Modules 102
- 5.3 Motherboard 103
- 5.4 EISA Bus Options 104
- 5.5 ISA Bus Options 105
- 5.6 EISA Configuration Utility 106
- 5.6.2 How to Start the ECU 107
- 5.6.3 Configuring EISA Options 109
- 5.6.4 Configuring ISA Options 110
- 5.7 PCI Bus Options 111
- 5.8 SCSI Buses 112
- 5.8.2 External SCSI Expansion 113
- 5.8.3 SCSI Bus Configurations 114
- 17-03969-01 120
- 5.10.1 set console 121
- 5.10.2 set tt_allow_login 122
- 5.10.3 set tga_sync_green 123
- Replacement 125
- Figure 6–1 FRUs, Front Right 129
- Figure 6–2 FRUs, Rear Left 130
- 6.2 Removal and Replacement 131
- Top Cover 132
- Release Latch 132
- 6.2.1 Cables 133
- Figure 6–7 Power Cord 134
- DC Cable 137
- Assembly 137
- 70-31346-01 138
- External 140
- Terminator 140
- StorageWorks 140
- Backplane 140
- 6.2.3 CPU Daughter Board 145
- 6.2.4 Fans 146
- 6.2.5 StorageWorks Drive 147
- Rear Screws 148
- 6/32 Inch (4) 148
- Internal Screws 148
- 3.5 mm (2) 148
- 6.2.7 Memory Modules 150
- 6.2.8 Interlock Switch 154
- 6.2.9 Motherboard 155
- ECC Banks 159
- 6.2.11 OCP Module 160
- 6.2.12 Power Supply 163
- 6.2.13 Speaker 164
- 6.2.14 Removable Media 165
- Default Jumper Settings 169
- A–2 Default Jumper Settings 170
- A–4 Default Jumper Settings 172
- Default Jumper Settings A–5 173
- Glossary 175
- Glossary–2 176
- Glossary–3 177
- Glossary–4 178
- Glossary–5 179
- Glossary–6 180
- Glossary–7 181
- Glossary–8 182
- Glossary–9 183
- Glossary–10 184
- Glossary–11 185
- Glossary–12 186
- Glossary–13 187
- Glossary–14 188
- Glossary–15 189
- Technical Support 197
- Electronic Orders 197
- BUSINESS REPLY MAIL 200
Související produkty a manuály pro Napájecí jednotky Alpha 1000
Napájecí jednotky Alpha 3000 Uživatelský manuál
(2 stránky)
(2 stránky)
Napájecí jednotky Alpha APP60S Provozní pokyny
(55 stránky)
(55 stránky)
Napájecí jednotky Alpha 1000 Uživatelský manuál
(5 stránky)
(5 stránky)
(8 stránky)
Napájecí jednotky Alpha Node Uživatelský manuál
(1 stránky)
(1 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.632 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce