Alpha 1000 Uživatelská příručka Strana 100
- Strana / 200
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Table 5–4 (Cont.) Environment Variables Set During System Configuration
Variable Attributes Function
tga_sync_green NV Sets the location of the SYNC signal generated by the
ZLXp-E PCI graphics accelerator (PBXGA).
This environment variable must be set correctly so that
the graphics monitor will synchronize. The parameter
is a bit mask, where the least significant bit (LSB) sets
the vertical SYNC for the first graphics card found, the
second for the second found, and so on.
The command
set tga_sync_green 00
sets all
graphics cards to synchronize on a separate vertical
SYNC line, as required by some monitors. See the
monitor documentation for all other information.
ff—Synchronizes the graphics monitor on systems
that do not use a ZLXp-E PCI graphics accelerator
(default setting).
00—Synchronizes the graphics monitor on systems
with a ZLXp-E PCI graphics accelerator.
tt_allow_login NV Enables or disables login to the SRM console firmware
on alternative console ports.
0—Disables login on alternative console ports.
1—Enables login on alternative console ports
(default setting).
If the console output device is set to ‘‘serial’’,
set
tt_allow_login 1
allows you to log in on the
primary COM1 port, or alternate COM2 port, or
the graphics monitor.
If the console output device is set to ‘‘graphics’’,
set tt_allow_login 1
allows you to log in
through either the COM1 or COM2 console port.
Key to variable attributes:
NV —- Nonvolatile. The last value saved by system software or set by console commands is
preserved across system initializations, cold bootstraps, and long power outages.
W —- Warm nonvolatile. The last value set by system software is preserved across warm bootstraps
and restarts.
Note
Whenever you use the
set
command to reset an environment variable,
you must initialize the system to put the new setting into effect. Initialize
5–22 System Configuration and Setup
- AlphaServer 1000A 1
- Service Guide 1
- Contents 3
- 3 Running System Diagnostics 4
- 4 Error Log Analysis 4
- A Default Jumper Settings 6
- Examples 6
- Intended Audience 11
- Conventions 12
- Related Documentation 12
- Troubleshooting Strategy 15
- 1.1.1 Problem Categories 16
- 1–8 Troubleshooting Strategy 22
- 1.3 Information Services 23
- 1–10 Troubleshooting Strategy 24
- Troubleshooting Strategy 1–11 25
- ....done 31
- 12345.done 31
- FAIL B:0 S:2 31
- 2.3 Power-Up Screen 35
- 2.3.1 Console Event Log 37
- 2.5 Storage Device LEDs 41
- Activity LED 42
- 2.8 Fail-Safe Loader 47
- 2.9 Power-Up Sequence 50
- 2.9.2 DC Power-Up Sequence 51
- 2.10.1 Serial ROM Diagnostics 51
- Running System Diagnostics 55
- 3.2 Command Summary 56
- 3.3 Command Reference 57
- 3.3.1 test 58
- 3.3.2 cat el and more el 61
- 3.3.3 memory 62
- 3.3.4 netew 64
- Testing an Ethernet Port: 65
- 3.3.5 network 66
- 3.3.6 net -s 68
- 3.3.7 net -ic 69
- 3.3.8 kill and kill_diags 70
- 3.3.9 show_status 71
- 3.5 DEC VET 72
- Error Log Analysis 73
- Error Log Analysis 4–3 75
- 4–4 Error Log Analysis 76
- 4.3 Event Record Translation 77
- 4–6 Error Log Analysis 78
- System Configuration and Setup 79
- 5.1.1 System Firmware 80
- >>> 81
- >>> set os_type NT 82
- >>> init 82
- Digital UNIX and OpenVMS 87
- Synopsis: 89
- Example: 89
- Key to variable attributes: 94
- Whenever you use the 100
- 5.2 System Bus Options 101
- 5.2.1 CPU Daughter Board 102
- 5.2.2 Memory Modules 102
- 5.3 Motherboard 103
- 5.4 EISA Bus Options 104
- 5.5 ISA Bus Options 105
- 5.6 EISA Configuration Utility 106
- 5.6.2 How to Start the ECU 107
- 5.6.3 Configuring EISA Options 109
- 5.6.4 Configuring ISA Options 110
- 5.7 PCI Bus Options 111
- 5.8 SCSI Buses 112
- 5.8.2 External SCSI Expansion 113
- 5.8.3 SCSI Bus Configurations 114
- 17-03969-01 120
- 5.10.1 set console 121
- 5.10.2 set tt_allow_login 122
- 5.10.3 set tga_sync_green 123
- Replacement 125
- Figure 6–1 FRUs, Front Right 129
- Figure 6–2 FRUs, Rear Left 130
- 6.2 Removal and Replacement 131
- Top Cover 132
- Release Latch 132
- 6.2.1 Cables 133
- Figure 6–7 Power Cord 134
- DC Cable 137
- Assembly 137
- 70-31346-01 138
- External 140
- Terminator 140
- StorageWorks 140
- Backplane 140
- 6.2.3 CPU Daughter Board 145
- 6.2.4 Fans 146
- 6.2.5 StorageWorks Drive 147
- Rear Screws 148
- 6/32 Inch (4) 148
- Internal Screws 148
- 3.5 mm (2) 148
- 6.2.7 Memory Modules 150
- 6.2.8 Interlock Switch 154
- 6.2.9 Motherboard 155
- ECC Banks 159
- 6.2.11 OCP Module 160
- 6.2.12 Power Supply 163
- 6.2.13 Speaker 164
- 6.2.14 Removable Media 165
- Default Jumper Settings 169
- A–2 Default Jumper Settings 170
- A–4 Default Jumper Settings 172
- Default Jumper Settings A–5 173
- Glossary 175
- Glossary–2 176
- Glossary–3 177
- Glossary–4 178
- Glossary–5 179
- Glossary–6 180
- Glossary–7 181
- Glossary–8 182
- Glossary–9 183
- Glossary–10 184
- Glossary–11 185
- Glossary–12 186
- Glossary–13 187
- Glossary–14 188
- Glossary–15 189
- Technical Support 197
- Electronic Orders 197
- BUSINESS REPLY MAIL 200
Související produkty a manuály pro Napájecí jednotky Alpha 1000
Napájecí jednotky Alpha 3000 Uživatelský manuál
(2 stránky)
(2 stránky)
Napájecí jednotky Alpha APP60S Provozní pokyny
(55 stránky)
(55 stránky)
Napájecí jednotky Alpha 1000 Uživatelský manuál
(5 stránky)
(5 stránky)
(8 stránky)
Napájecí jednotky Alpha Node Uživatelský manuál
(1 stránky)
(1 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.508 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce