Alpha 1000 Uživatelská příručka Strana 91
- Strana / 182
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
The ECU is supplied on the two System Configuration Diskettes shipped with
the system. Make a backup copy of the system configuration diskette and keep
the original in a safe place. Use the backup copy when you are configuring
the system. The system configuration diskette must have the volume label
‘‘SYSTEMCFG.’’
Note
The CFG files supplied with the option you want to install may not work
on this system if the option is not supported. Before you install an option,
check that the system supports the option.
5.6.1 Before You Run the ECU
Before running the ECU:
1. Install EISA option(s). (Install ISA boards after you run the ECU.)
For information about installing a specific option, refer to the documentation
for that option.
2. Familiarize yourself with the utility.
You can find more information about the ECU by reading the ECU online
help. To read the online help, start the ECU (refer to Section 5.6.2). Online
help for the ECU is located under Step 1, ‘‘Important EISA Configuration
Information.’’
3. Familiarize yourself with the configuration procedure for the system:
• If you are configuring an EISA bus that contains only EISA options, refer
to Table 5–6.
• If you are configuring an EISA bus that contains both ISA and EISA
options, refer to Table 5–7.
4. Locate the ECU diskette for your operating system. The ECU diskette
is shipped in the accessories box with the system. Make a copy of the
appropriate diskette and keep the original in a safe place. Use the backup
copy for configuring options. The diskettes are labeled as follows:
• ECU Diskette DECpc AXP (AK-PYCJ*-CA) for Windows NT
• ECU Diskette DECpc AXP (AK-Q2CR*-CA) for DEC OSF/1 and
OpenVMS
System Configuration and Setup 5–23
- AlphaServer1000 1
- ServiceGuide 1
- Contents 3
- 3 Running System Diagnostics 4
- 4 Error Log Analysis 4
- A Default Jumper Settings 6
- Examples 6
- Intended Audience 11
- Conventions 11
- Related Documentation 12
- Troubleshooting Strategy 13
- 1.1.1 Problem Categories 14
- 1–8 Troubleshooting Strategy 20
- 1.3 Information Services 21
- 1.2.3.done 26
- 2.2 Power-Up Screen 29
- 2.2.1 Console Event Log 30
- 2.4 Storage Device LEDs 33
- Activity 34
- Activity LED 34
- 2.7 Fail-Safe Loader 39
- 2.8 Power-Up Sequence 41
- 2.8.2 DC Power-Up Sequence 42
- 2.9.1 Serial ROM Diagnostics 42
- Running System Diagnostics 45
- 3.2 Command Summary 46
- 3.3 Command Reference 47
- 3.3.1 test 48
- 3.3.2 cat el and more el 51
- 3.3.3 memory 52
- 3.3.4 netew 54
- Testing an Ethernet Port: 55
- 3.3.5 network 56
- 3.3.6 net -s 58
- 3.3.7 net -ic 59
- 3.3.8 kill and kill_diags 60
- 3.3.9 show_status 61
- 3.5 DEC VET 62
- Error Log Analysis 63
- Error Log Analysis 4–3 65
- 4–4 Error Log Analysis 66
- 4.3 Event Record Translation 67
- 4–6 Error Log Analysis 68
- System Configuration and Setup 69
- 5.1.1 System Firmware 70
- >>> 71
- OSF/1 and OpenVMS 77
- Synopsis: 78
- Example: 78
- Key to variable attributes: 81
- 5.2 System Bus Options 85
- ECC Banks 86
- 5.2.1 CPU Daughter Board 87
- 5.2.2 Memory Modules 87
- 5.3 Motherboard 88
- 5.4 EISA Bus Options 89
- 5.5 ISA Bus Options 89
- 5.6 EISA Configuration Utility 90
- 5.6.1 Before You Run the ECU 91
- 5.6.2 How to Start the ECU 92
- 5.6.3 Configuring EISA Options 93
- 5.6.4 Configuring ISA Options 94
- 5.7 PCI Bus Options 96
- 5.8 SCSI Buses 96
- 17-03969-01 104
- Replacement 107
- Figure 6–1 FRUs, Front Right 110
- Figure 6–2 FRUs, Rear Left 111
- 6.2 Removal and Replacement 112
- Top Cover 113
- Release Latch 113
- 6.2.1 Cables 114
- 17-03971-01 115
- Figure 6–7 Power Cord 116
- DC Cable 118
- Assembly 118
- • Power supply +3.3V (20-pin) 119
- (50-Pin) 124
- 6.2.2 CPU Daughter Board 128
- 6.2.3 Fans 129
- Figure 6–20 Removing Fans 130
- 6.2.4 StorageWorks Drive 131
- 6.2.6 Memory Modules 134
- 6.2.7 Interlock Switch 138
- 6.2.8 Motherboard 139
- NEW MOTHERBOARD 142
- 6.2.10 OCP Module 143
- 6.2.11 Power Supply 146
- 6.2.12 Speaker 147
- 6.2.13 Removable Media 148
- Default Jumper Settings 151
- A.1 Motherboard Jumpers 152
- A–4 Default Jumper Settings 154
- Default Jumper Settings A–5 155
- Glossary 157
- Glossary–2 158
- Glossary–3 159
- Glossary–4 160
- Glossary–5 161
- Glossary–6 162
- Glossary–7 163
- Glossary–8 164
- Glossary–9 165
- Glossary–10 166
- Glossary–11 167
- Glossary–12 168
- Glossary–13 169
- Glossary–14 170
- Glossary–15 171
- Technical Support 179
- Electronic Orders 179
- BUSINESSREPLYMAIL 182
Související produkty a manuály pro Napájecí jednotky Alpha 1000
Napájecí jednotky Alpha Lectro 87V Návod k obsluze
(36 stránky)
(36 stránky)
Napájecí jednotky Alpha 700 Uživatelský manuál
(4 stránky)
(4 stránky)
Napájecí jednotky Alpha 3000 Manuál s instrukcemi
(314 stránky)
(314 stránky)
Napájecí jednotky Alpha 1000 Uživatelská příručka
(200 stránky)
(200 stránky)
Napájecí jednotky Alpha 3000 Uživatelský manuál
(2 stránky)
(2 stránky)
Napájecí jednotky Alpha APP60S Provozní pokyny
(55 stránky)
(55 stránky)
Napájecí jednotky Alpha 1000 Uživatelský manuál
(5 stránky)
(5 stránky)
(8 stránky)
Napájecí jednotky Alpha Node Uživatelský manuál
(1 stránky)
(1 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 2.397 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce