Alpha 1000A Specifikace Strana 91
- Strana / 218
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
AlphaServer 1000A Owner's Guide Installing and Removing Components • 5-11
Installing an Option Card
To install a PCI, EISA, or ISA option card on the system board, refer to Figures 5-8
and 5-9, and follow the steps below.
Note: If you want to install a high-performance graphics
option card, you must disable the SVGA jumper (J27) on
the system board. Figure 9-6 in Chapter 9, "Quick
Reference" shows the jumper location.
If you are running the Digital UNIX or OpenVMS Alpha
operating system, run the EISA Configuration Utility
(ECU) and disable the on-board VGA using the "View or
Edit Details" ECU option. See "Configuring EISA
Options" in Chapter 4, "Basic Operations."
Caution: Static electricity can damage
electronic components. Use an antistatic
wrist strap while handling these components.
(See "Antistatic Precautions.")
1. Select a vacant option card slot on the system board. The top two slots are
reserved for EISA or ISA options; the bottom seven are for PCI options. Figure
5-8 shows examples of the three kinds of option cards.
- AlphaServer 1000A 1
- Owner's Guide 1
- February 1996 2
- October 1996 2
- ACOUSTIC DECLARATION: 3
- Contents 5
- About This Guide 11
- Organization 12
- Conventions 13
- Related Documentation 14
- 1 Overview 15
- Supported Operating Systems 16
- System Console Firmware 16
- System Features 18
- Server Management 19
- System Security 19
- 8 9 10 11 20
- Front Panel Switches 22
- Rear Panel Ports and Slots 23
- Internal System Options 24
- PCI, EISA, and ISA Options 25
- Memory Options 25
- External Options 26
- Ordering Options 26
- 2 Hardware Installation 27
- Selecting a System Location 28
- Power Requirements 29
- Identifying Accessories 30
- Optional Accessories 31
- Verifying Hardware Setup 33
- Locking Your System 34
- Key Number 35
- Location 35
- Introduction 37
- Updating the Firmware 39
- Preparing Your Hard Disk 41
- Installation Preparation 43
- Installing Digital UNIX 44
- Preparing the System 44
- Preparing Software Components 45
- Installing OpenVMS Alpha 46
- 4 Basic Operation 47
- On/Off Switch In 48
- ("On" Position) 48
- On/Off Switch Out 48
- ("Off" Position) 48
- Turning the System Off 49
- Interpreting Startup Messages 51
- Using the Consoles 53
- When to Switch Consoles 54
- >>> set os_type nt 55
- Boot Menu Functions 56
- Supplementary Menu Functions 56
- Setup Menu Functions 57
- Basic Commands 57
- Caution: 58
- SRM Console Security Features 59
- The login Command 60
- The clear password Command 61
- Setup Menu 62
- Setup Menu Help 63
- Booting the Operating System 65
- Verify Your Configuration 68
- Booting Windows NT 69
- Using Storage Drives 72
- Figure 4-2 Storage Devices 73
- Using a Diskette Drive 74
- Using a CDROM Drive 75
- Caring for Your System 78
- Cleaning Your Keyboard 79
- Moving Your System 79
- Packing Your System 79
- 5 Installing and Removing 81
- Components 81
- Required Equipment 82
- Antistatic Precautions 82
- Top Cover and Side Panels 83
- Top Cover 84
- Release Latch 84
- Memory Modules 86
- Removing Memory Modules 87
- Installing Memory Modules 88
- Installing an Option Card 91
- Removing an Option Card 93
- Cover and Side Panels." 94
- Identifying the Drive Bays 97
- Installing a Tape Drive 98
- Removing a Tape Drive 99
- Installing a CDROM Drive 100
- Removing a CDROM Drive 100
- Data Cable 101
- Power Cable 101
- Installing a Diskette Drive 102
- Removing a Diskette Drive 103
- Power Supply 104
- Removing the Power Supply 106
- CPU Card 107
- Installing the CPU Card 108
- 6 Configuring 109
- The show config Command 112
- >>> 114
- The show device Command 116
- The show memory Command 117
- The set and show Commands 117
- Options: 118
- Figure 6-2 Memory Banks 119
- Network Connections 120
- Keyboard Type 121
- EISA and ISA Options 122
- Before You Run the ECU 125
- Configuring EISA Options 126
- Configuring ISA Options 128
- PCI Option Cards 130
- Storage Devices 131
- SCSI Device Configurations 133
- Optional 136
- Terminator 136
- Dual-Controller Configuration 138
- 7 Upgrading 149
- Access from the Internet 151
- Upgrade Options 152
- APU-> update 154
- APU-> verify 154
- 8 Troubleshooting 157
- Troubleshooting Overview 158
- System Diagnostics 159
- Reading the Console Event Log 160
- The test Command 160
- The show_status Command 162
- Power Problems 163
- Console Problems 163
- Boot Problems 165
- Storage Problems 168
- Option Card Problems 170
- Monitor and Terminal Problems 171
- Possible Cause Action 172
- Keyboard and Mouse Problems 173
- Printer Problems 173
- Overheating Problems 174
- RAID Device Problems 174
- Using the Fail-Safe Loader 175
- 9 Quick Reference 177
- Hardware Overview 178
- System Rear View 179
- System Side View 180
- ECC Banks 182
- Port Pinouts 183
- Parallel Port Connector 184
- Serial Port Connectors 185
- SCSI Port Connector 186
- Indicator Lights 187
- VGA Enable (J27) 189
- Large Fan (J16) 189
- Model 4/266 190
- Model 4/233 191
- A2 A1 A0 WS EP SS 192
- SCSI ID Settings 193
- Specifications 196
- System Architecture 198
- Glossary of Terms 199
- Windows NT 211
Související produkty a manuály pro Servery Alpha 1000A
Servery Alpha 1000A Technické informace
(28 stránky)
(28 stránky)
Servery Alpha 1000A Instalační manuál
(28 stránky)
(28 stránky)
Servery Alpha 1000A Manuál s instrukcemi
(67 stránky)
(67 stránky)
Servery Alpha 1000A Uživatelský manuál
(2 stránky)
(2 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce